spec.dock BMW 5-Series e60 v.2 Installation Instructions
spec.dock iPod solution for your vehicle. Audio connections may vary according to your particular setup. 2point5 recommends having your spec.dock integrated by a certified professional installer.
Begin by using a panel tool to pry the dash trim up on the right hand side. If the vehicle has woodgrain trim, be especially careful to pry gently, as the clearcoat on the trim will chip easily. Only move the trim out far enough to enable using your fingers to unsnap the rest of the piece.
Read more
2000-2003 Ford Taurus PART 99-5718 Installation Instructions
FORD TAURUS 2000-2003 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Using Metra’s 86-5618, pull the factory radio/climate control panel from the dash. (Fig. A) 3 Disconnect the audio system connectors, blower motor switch connector, vacuum hose harness, a/c damper door switch connector, and potentiometer connector. Remove the panel. 4 Remove (2) torx-head screws securing the mounting clips to the sides of the factory radio/climate control panel and remove the clips. (Fig. B) 5 Mount the clips to the Integrated Mounting Kit with the same torx-head screws.
Read more
1998-2008 Volkswagen New Beetle Convertible Cylinder Head
Removing Requirement The engine must be no more than warm to touch. Procedure First, check whether a coded radio is installed. If necessary, obtain the anti-theft coding. With the ignition switched off disconnect battery ground strap. Remove engine cover. Drain the coolant Cooling System, Draining and Filling . Disconnect the remove the Secondary Air Injection (AIR) pump motor and bracket Secondary Air Injection System Components Assembly Overview.
Read more
G-TECH/Pro EGS - Expandable Gauge System
I would like to take this opportunity to thank you, our customer, for all the years of support. Without your appreciation of our products the effort we put behind all the research and development wouldn’t be nearly as gratifying.
Judging by the thickness of this manual one could easily be intimidated. Not to worry, EGS is set up to be as simple or as involved as you want it to be. You can customize your EGS “as you go”, by adding modules and expanding the functionality of your system at any time. This gives you an opportunity to get familiar with the gauge and then build-up a very powerful system that can give you a complete “window to your car’s soul” regardless if you have a ’69 Camaro or a modern-day Honda.
Read more
2010 Toyota Prius Dual Player Headrest Video
Pre-installation Precaution
1. Use Seat and Floor Protectors to avoid damage to surfaces.
2. If the vehicle is equipped with an Anti-theft radio, the radio code must be written down prior to disconnecting the battery cable. The code must be re-entered when the negative battery cable is reinstalled. Disconnecting the battery may cause certain vehicle settings to be lost. Manufacture’s recommendations for the battery removal should be followed. Disconnecting the battery is recommended.
Read more
2010 Uconnect User’s Manual
Acting as the link to the world around you, the available Uconnect™ systems in your vehicle provide access to information, entertainment and technology. This Uconnect™ User’s Manual consists of the follow systems:
• Uconnect™ Phone
Uconnect™ Phone is a voice-activated, hands-free, in-vehicle communications system. Uconnect™ Phone allows you to dial a phone number with your cellular phone using simple voice commands (e.g., Call” “Mike” ”Work or Dial” “248-555-1212).
• Uconnect™ Multimedia – Video Entertainment System (VES)™ Video Entertainment System (VES)™ is designed to give your family years of enjoyment. You can play your favorite DVDs, watch SIRIUS Backseat TV™ (if equipped), listen to audio over the wireless head- phones and play a variety of standard video games or audio devices.
Read more
Activinterface AUDI/VW Instruction Manual
This adaptor is for use for in following cars: Connects aftermarket headunits to OEM systems in AUDI A-series, PASSAT DSP, GOLF DSP (4/98on) PORSCHE 996, BOXSTER with active front and rear, or passive front and active rear speakers, max. 4*50 W. Also suitable for AUDI BOSE systems. Not suitable for VW cars with 4:3 navigation MFD1.
Read more
Backup Camera Input Module for Audi 3G Multi Media Interface System
Installation:
1. Locate a fiber optic connection somewhere in the vehicle. Recommended location would be in the back of the vehicle where the multimedia equipment is located. Usually located on either side of the rear of the vehicle.
2. Remove the fiber optic connector from any optical unit, and then assemble per Optical Cable Connections diagram (see last page.)
3. Once connector is reassembled, reconnect to original unit then connect the new connector into the backup camera module.
4. Power for the backup camera module can be spliced into any good continuous power and ground point. (Verify with a multi-meter.)
5. The blue wire from the backup camera module needs to be connected to the vehicle’s reverse light wire. This wire is usually located by the multimedia equipment in the rear of the vehicle. (Using a multi-meter, the wire will show +12 volts when the vehicle is in reverse.)
Read more
mObridge Audio iPod & Bluetooth Install Notes
The mObridge main power connector contains the optical fiber input as well as a 4 pin wiring insert. This 4 pin wiring insert, if inspected closely, has numbering on the pins. Although both the BMW and mObridge share the same connector as the BMW CDC and Sat Radio wiring, the pinning is slightly different. If the user tries to plug the connetor directly in without changing the BMW plug wiring into the mObridge unit, the user will burn a fuse out in the vehicle.
Read more
2010 ARVO-TEC Feeding Robot Installation Manual
Arvo-Tec Robot system installation procedure
1. Send site layout to Arvo-Tec distributor or directly to Arvo-Tec with your comments and wishes. If you have any question or doubts please do not hesitate to contact.
2. Install the rail. Follow details in the chapter “Instructions for rail installation”. Lift robot to the rail and run it while installation proceed to test the rail immediately. You can use robot manual drive forward and backwards functions. Use the lowest possible 25% speed and be ready to stop the robot if needed. Refer to robot user manual for details how to run robot.
3. Install electricity supply to the filling system and robot charger.
4. Install filling system mechanical parts: reserve silos, augers, etc.
5. Install robot home station battery charging system and filling system home switch.
Read more
