Camaro Drop Spring Installation
Front Spring Replacement
Lift the car and support it properly. This installation can either be done on jack stands or on a lift. Open the hood and remove the plastic cover from the upper strut nuts and the upper nut and plate on each side - See Figure 1 and Figure 2. This nut is 24 mm. This may allow the strut to lower from the tower, but most likely it will be stuck in place still.
Caution! the second nut holds the spring tension, do not remove that yet. Lift the vehicle and remove both front tires.
Read more
2010 Camaro Installation Instructions
Section 1 A Removing factory engine cover.
Twist and remove the oil fill cap as shown. Pull up and pull towards the front of the car. This will release the cover.
Section 1B - Removing the factory air box
1. Remove factory bolts (10mm X2)
2. Unplug air meter wiring harness by squeezing and pulling on the harness plug.
3. Loosen hose clamps (3 clamps, 6mm driver or flathead screwdriver) and remove factory intake air tube.
4. Lift air box straight out by pulling up, it will release with a pop! (there is a grommet under the box)
Read more
2010 Chevrolet Camaro Borla Exhaust System Installation
This Borla Performance Cat-back™ Exhaust System (Part number 140280, 140281) has been designed for 2010 Chevrolet Camaro equipped with a 6.2L V-8 engine and automatic or manual transmissions. Borla Performance Cat-back™ Exhaust System (part number 140282) has been designed for 2010 Chevrolet Camaro equipped with a 3.6L V-6 engine with an automatic or manual transmission.
Read more
2010 Chevy Camaro 3.6L V6 Shortie Header System THY-338-C Installation
The installation of headers onto any vehicle must be performed in accordance with all govern- mental regulations that might pertain to the particular vehicle receiving the headers. Please call your Thorley Headers distributor if there are any questions regarding the legality of the installation.
Installation Notes:
1) It is important that you read the entire instruction sheet before initiating any installation.
2) Due to restricted room in the engine compartment, your headers may come close to certain body and chassis components. This is normal Read more
2010 Chevrolet Camaro DefenderWorx Replacement Bowtie Installation Instructions
The bowtie installation procedure for this chevrolet camaro:
Front Bowtie: Reach both hands underneath the factory bowtie housing (whole chrome piece) on each side. Feel around for the two clips on the back of the bowtie housing. Pull both of the clips down and forcefully pull/wiggle the bowtie housing out. Flip over the housing and poke out the gold bowtie through the back using a flat head screwdriver and the four holes on the back of the bowtie housing unit. Clean the area and replace with the DefenderWorx Bowtie. Snap the bowtie housing back into place on the grill and enjoy your new DefenderWorx Replacement Bowtie.
Read more
2010 427HP & 454HP Camaro
SLP PowerFlo® Axle-Back Exhaust System with 4” Dual Wall Tips – SLP’s axle-back exhaust system was designed and tuned specifically for the new Camaro ZL®. The resulting tone is deep, rich and powerful - a perfect blend of Muscle Car and Grand-Touring sound quality. The system features polished 304 stainless steel mufflers, mandrel-bent stainless steel pipes and 4” diameter, dual-wall, uniquely shaped exhaust tips that fit the factory rear fascia openings.
Note: Units equipped with GM dealer installed ground effects will receive the appropriate tips to fit the openings.
Read more
2010 Chevy Camaro Sport Sway Bar Kit 22109 Instructions
Front Sway Bar Installation
1. Raise the Vehicle
Raise front of the vehicle using a floor jack and place jack stands in the proper jacking points. Securely block the rear wheels of the vehicle.
2. Remove the Driver Side Front Wheel
The front bar will sneak it’s way out towards the driver side. Remove the driver side front wheel to gain more clearance for installation.
3. Disconnect the Front End Links
Disconnect the front end links from the sway bar ends on each side.
Read more
Keychain Radio Remote Control System Service Manual
This Ricon service manual is for use by qualified service. technicians, and is not intended for ….. CHEVROLET. Light Brown with White stripe. FULL SIZE …
Read more
Chevrolet Timing Chain Tools and Supplies needed Kit Components
Chevrolet Timing Chain. Thank you for choosing COMP Cams® products; …. your repair manual for the proper torque specifications for all attaching hardware …
Read more
MERICA USDOE 1998 Chevrolet S-10 Electric w/NiMH
1998 Chevrolet S-10 Electric. w/NiMH. VEHICLE SPECIFICATIONS … As detailed in the Owners Manual, the Battery Life and Service Soon telltales illuminated …
Read more
